Gen. Sherman’s Railroad Sabotage Tricks Shattered the Confederacy’s War Effort

Photo Credit: 1. Bubba73 / Jud McCranie / Wikimedia Commons CC BY-SA 4.0 2. Civil War Glass Negatives / Wikimedia Commons / Public Domain

Sherman’s Neckties, sometimes referred to as Sherman’s Bowties, Jeff Davis’s Neckties, or Sherman’s Hairpins, were methods employed by the Union Army during the American Civil War to disrupt railroad operations. Developed by Major General William Tecumseh Sherman, these tactics sought to cripple the Confederacy’s strategic and economic assets by specifically targeting its railway systems.

The Union Army needed to slow down the Confederates

Sherman’s Neckties along a Confederate railroad. (Photo Credit: Hal Jespersen / US Army Military History Institute / Wikimedia Commons / Public Domain)

As the Civil War approached its conclusion, the Union sought a method to cripple the Confederates, identifying their vulnerable point in the form of limited iron supplies and foundries. In the summer of 1864 during the Atlanta Campaign, Sherman issued orders for the Union Army to focus on dismantling the enemy’s rail systems to sever Confederate troops from their crucial supply lines.

The directive, issued on July 18, 1864, stated:

“In case of the sounds of serious battle he will close in on General Schofield, but otherwise will keep every man of his command at work in destroying the railroad by tearing up track, burning the ties and iron, and twisting the bars when hot. Officers should be instructed that bars simply bent may be used again, but if when red hot they are twisted out of line they cannot be used again.

“Pile to ties into shape for a bonfire, put the rails across, and when red hot in the middle, let a man at each end twist the bar so that its surface become spiral. General McPherson will dispatch General Garrard’s cavalry eastward along the line of the railroad to continue the destruction as far as deemed prudent.”

This marked the initiation of Sherman’s Neckties. After a mere three days, all but one railroad line in Atlanta had been effectively dismantled.

The first way to make Sherman’s Neckties

Sherman’s Necktie. (Photo Credit: Thomas Cizauskas / Flickr CC BY-NC-ND 2.0)

Merely destroying the railroad tracks did not adequately disrupt the Confederate supply lines. Even after Union forces dismantled the tracks, they were unable to completely remove the rails, making it easy for the Confederates to reassemble them.

To tackle this problem, Sherman instructed his troops to remove the tracks from the ties and place them vertically across a bonfire. As the metal heated, its weight caused it to warp. Nevertheless, this method was not entirely effective, as it only partially distorted the rails. With enough effort, Confederate troops could realign the rails and quickly restore the tracks to their original state.

Related Post

The second way to make Sherman’s Neckties 

A Sherman’s Necktie. (Photo Credits: Bubba73 (Jud McCranie) / Wikimedia Commons CC BY-SA 4.0).

The soldiers on the ground developed a more efficient technique for bending the rails, making them entirely unusable. They would use the heat from a bonfire to heat the rail until it was glowing red, then wrap it around a tree, twisting it until the ends overlapped.

These twisted rails, left hanging on the trees, became known as Sherman’s Neckties. The Confederates didn’t have the foundry capacity to melt down the rails or the manpower to lay new tracks.

Meridian Campaign of 1864

Sherman’s Necktie. (Photo Credit: Gary Todd / Flickr CC0 1.0)

The town of Meridian, situated in eastern Mississippi, held a lot of strategic value for the Confederate Army due to its intersection of three vital railroads and its role as a hub for storing and distributing agricultural goods for Southern military operations.

Recognizing Meridian’s importance, Sherman aimed to intercept and destroy Confederate access to these railroads. By achieving this objective, Union forces could effectively limit Confederate mobility as they advanced towards the Mississippi River during their March to the Sea Campaign.

On February 3, 1864, Union troops started the campaign “to break up the enemy’s railroads at and about Meridian, and to do the enemy as much damage as possible in the month of February, and to be prepared by the 1st of March to assist General [Nathaniel] Banks in a similar dash at the Red River country.”

The Impact of Sherman’s Neckties 

William Sherman sitting with his generals. Sherman is second from the left sitting. (Photo Credits: Unknown Author /Library of Congress, Prints & Photographs Division, Civil War Photographs / Reproduction number LC-DIG-ppmsca-66656 / Wikimedia Commons / Public Domain).

When Sherman’s men arrived in Meridian on February 14, they immediately began prying up the railroad tracks, leaving only Sherman’s Neckties in their wake. They completed their objective and returned to Vicksburg by March 6. It took the Confederates 26 days to restore the rails.

Want War History Online‘s content sent directly to your inbox? Sign up for our newsletter here!

The sabotage put the South’s rail lines out of commission for nearly a month, critically impacting their position in the war and proving that Sherman’s Neckties were an effective tactic.

Samantha Franco: Samantha Franco is a Freelance Content Writer who received her Bachelor of Arts degree in history from the University of Guelph, and her Master of Arts degree in history from the University of Western Ontario. Her research focused on Victorian, medical, and epidemiological history with a focus on childhood diseases. Stepping away from her academic career, Samantha previously worked as a Heritage Researcher and now writes content for multiple sites covering an array of historical topics. In her spare time, Samantha enjoys reading, knitting, and hanging out with her dog, Chowder!
Leave a Comment